4 * This file is part of BeRTOS.
6 * Bertos is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License as published by
8 * the Free Software Foundation; either version 2 of the License, or
9 * (at your option) any later version.
11 * This program is distributed in the hope that it will be useful,
12 * but WITHOUT ANY WARRANTY; without even the implied warranty of
13 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
14 * GNU General Public License for more details.
16 * You should have received a copy of the GNU General Public License
17 * along with this program; if not, write to the Free Software
18 * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
20 * As a special exception, you may use this file as part of a free software
21 * library without restriction. Specifically, if other files instantiate
22 * templates or use macros or inline functions from this file, or you compile
23 * this file and link it with other files to produce an executable, this
24 * file does not by itself cause the resulting executable to be covered by
25 * the GNU General Public License. This exception does not however
26 * invalidate any other reasons why the executable file might be covered by
27 * the GNU General Public License.
29 * Copyright 2008 Develer S.r.l. (http://www.develer.com/)
30 * All Rights Reserved.
33 * \brief Configuration file for serial module.
37 * \author Daniele Basile <asterix@develer.com>
44 * Example of setting for serial port and
46 * Edit these define for your project.
49 #define CONFIG_SER_PORT 0
50 #define CONFIG_SER_BAUDRATE 115200
53 #define CONFIG_SPI_PORT 0
54 #define CONFIG_SPI_BAUDRATE 5000000UL
57 /// [bytes] Size of the outbound FIFO buffer for port 0.
58 #define CONFIG_UART0_TXBUFSIZE 32
60 /// [bytes] Size of the inbound FIFO buffer for port 0.
61 #define CONFIG_UART0_RXBUFSIZE 32
63 /// [bytes] Size of the outbound FIFO buffer for port 1.
64 #define CONFIG_UART1_TXBUFSIZE 32
66 /// [bytes] Size of the inbound FIFO buffer for port 1.
67 #define CONFIG_UART1_RXBUFSIZE 32
70 /// [bytes] Size of the outbound FIFO buffer for SPI port (AVR only)
71 #define CONFIG_SPI_TXBUFSIZE 32
73 /// [bytes] Size of the inbound FIFO buffer for SPI port (AVR only)
74 #define CONFIG_SPI_RXBUFSIZE 32
76 /// [bytes] Size of the outbound FIFO buffer for SPI port 0.
77 #define CONFIG_SPI0_TXBUFSIZE 32
79 /// [bytes] Size of the inbound FIFO buffer for SPI port 0.
80 #define CONFIG_SPI0_RXBUFSIZE 32
82 /// [bytes] Size of the outbound FIFO buffer for SPI port 1.
83 #define CONFIG_SPI1_TXBUFSIZE 32
85 /// [bytes] Size of the inbound FIFO buffer for SPI port 1.
86 #define CONFIG_SPI1_RXBUFSIZE 32
88 /// SPI data order (AVR only).
89 #define CONFIG_SPI_DATA_ORDER SER_MSB_FIRST
91 /// SPI clock division factor (AVR only).
92 #define CONFIG_SPI_CLOCK_DIV 16
94 /// SPI clock polarity: 0 = normal low, 1 = normal high (AVR only).
95 #define CONFIG_SPI_CLOCK_POL 0
97 /// SPI clock phase: 0 = sample on first edge, 1 = sample on second clock edge (AVR only).
98 #define CONFIG_SPI_CLOCK_PHASE 0
100 /// Default transmit timeout (ms). Set to -1 to disable timeout support.
101 #define CONFIG_SER_TXTIMEOUT -1
103 /// Default receive timeout (ms). Set to -1 to disable timeout support.
104 #define CONFIG_SER_RXTIMEOUT -1
106 /// Use RTS/CTS handshake
107 #define CONFIG_SER_HWHANDSHAKE 0
109 /// Default baud rate (set to 0 to disable).
110 #define CONFIG_SER_DEFBAUDRATE 0
112 /// Enable ser_gets() and ser_gets_echo().
113 #define CONFIG_SER_GETS 0
115 /// Enable second serial port in emulator.
116 #define CONFIG_EMUL_UART1 0
119 * Transmit always something on serial port 0 TX
120 * to avoid interference when sending burst of data,
121 * using AVR multiprocessor serial mode
123 #define CONFIG_SER_TXFILL 0
125 /// For serial debug.
126 #define CONFIG_SER_STROBE 0
128 #endif /* CFG_SER_H */