Merge branch "preempt" in "trunk".

[bertos.git] / bertos / cpu / avr / drv / ser_avr.c

diff --git a/bertos/cpu/avr/drv/ser_avr.c b/bertos/cpu/avr/drv/ser_avr.c
index 746bb5270feb6a88eaed545839537975ee4926fe..d6de8243dbb27056be9a71158b2d97090bd97da2 100644 (file)
--- a/bertos/cpu/avr/drv/ser_avr.c
+++ b/bertos/cpu/avr/drv/ser_avr.c
@@ -454,9 +454,7 @@ static void spi_init(UNUSED_ARG(struct SerialHardware *, _hw), UNUSED_ARG(struct
         * - as input but tied high forever!
         * This driver set the pin as output.
         */
-       #if !(ARCH & ARCH_NIGHTTEST)
-               #warning SPI SS pin set as output for proper operation, check schematics for possible conflicts.
-       #endif
+       #warning FIXME:SPI SS pin set as output for proper operation, check schematics for possible conflicts.
        ATOMIC(SPI_DDR |= BV(SPI_SS_BIT));
 
        ATOMIC(SPI_DDR &= ~BV(SPI_MISO_BIT));
@@ -647,7 +645,7 @@ struct SerialHardware *ser_hw_getdesc(int unit)
 #if CONFIG_SER_HWHANDSHAKE
 
 /// This interrupt is triggered when the CTS line goes high
-SIGNAL(SIG_CTS)
+DECLARE_ISR(SIG_CTS)
 {
        // Re-enable UDR empty interrupt and TX, then disable CTS interrupt
        UCSR0B = BV(BIT_RXCIE0) | BV(BIT_UDRIE0) | BV(BIT_RXEN0) | BV(BIT_TXEN0);
@@ -660,7 +658,7 @@ SIGNAL(SIG_CTS)
 /**
  * Serial 0 TX interrupt handler
  */
-SIGNAL(USART0_UDRE_vect)
+DECLARE_ISR(USART0_UDRE_vect)
 {
        SER_STROBE_ON;
 
@@ -708,7 +706,7 @@ SIGNAL(USART0_UDRE_vect)
  * otherwise we'd stop the serial port with some data
  * still pending in the buffer.
  */
-SIGNAL(SIG_UART0_TRANS)
+DECLARE_ISR(SIG_UART0_TRANS)
 {
        SER_STROBE_ON;
 
@@ -731,7 +729,7 @@ SIGNAL(SIG_UART0_TRANS)
 /**
  * Serial 1 TX interrupt handler
  */
-SIGNAL(USART1_UDRE_vect)
+DECLARE_ISR(USART1_UDRE_vect)
 {
        SER_STROBE_ON;
 
@@ -769,7 +767,7 @@ SIGNAL(USART1_UDRE_vect)
  *
  * \sa port 0 TX complete handler.
  */
-SIGNAL(USART1_TX_vect)
+DECLARE_ISR(USART1_TX_vect)
 {
        SER_STROBE_ON;
 
@@ -804,7 +802,7 @@ SIGNAL(USART1_TX_vect)
  *       RXCIE is cleared.  Unfortunately the RXC flag is read-only
  *       and can't be cleared by code.
  */
-SIGNAL(USART0_RX_vect)
+DECLARE_ISR(USART0_RX_vect)
 {
        SER_STROBE_ON;
 
@@ -852,9 +850,9 @@ SIGNAL(USART0_RX_vect)
  * is heavily loaded, because an interrupt could be retriggered
  * when executing the handler prologue before RXCIE is disabled.
  *
- * \see SIGNAL(USART1_RX_vect)
+ * \see DECLARE_ISR(USART1_RX_vect)
  */
-SIGNAL(USART1_RX_vect)
+DECLARE_ISR(USART1_RX_vect)
 {
        SER_STROBE_ON;
 
@@ -895,7 +893,7 @@ SIGNAL(USART1_RX_vect)
 /**
  * SPI interrupt handler
  */
-SIGNAL(SIG_SPI)
+DECLARE_ISR(SIG_SPI)
 {
        SER_STROBE_ON;