Remove duplicate define. Put all phy chip specific defines in its

[bertos.git] / bertos / cpu / cortex-m3 / drv / ser_sam3.c

diff --git a/bertos/cpu/cortex-m3/drv/ser_sam3.c b/bertos/cpu/cortex-m3/drv/ser_sam3.c
index 0c5f8c3988b5124767cb833a581859f2abf663c1..c330ca80acc382b9c335c82c782e4658166dbe27 100644 (file)
--- a/bertos/cpu/cortex-m3/drv/ser_sam3.c
+++ b/bertos/cpu/cortex-m3/drv/ser_sam3.c
@@ -91,6 +91,7 @@
        #endif
        #define SER_UART0_BUS_TXINIT do { \
                PIOA_PDR = BV(RXD0) | BV(TXD0); \
+               PIO_PERIPH_SEL(PIOA_BASE, BV(RXD0) | BV(TXD0), USART0_PERIPH); \
        } while (0)
 #endif
 
@@ -119,7 +120,7 @@
 
 /* End USART0 macros */
 
-#if !CPU_CM3_AT91SAM3U
+#if USART_PORTS > 1
 
        #ifndef SER_UART1_BUS_TXINIT
                /**
@@ -127,20 +128,13 @@
                 *
                 * - Disable GPIO on USART1 tx/rx pins
                 */
-               #if CPU_ARM_AT91
-                       #if !CPU_ARM_SAM7S_LARGE && !CPU_ARM_SAM7X
-                               #warning Check USART1 pins!
-                       #endif
-                       #define SER_UART1_BUS_TXINIT do { \
-                               PIOA_PDR = BV(RXD1) | BV(TXD1); \
-                       } while (0)
-               #elif CPU_CM3_AT91SAM3
-                       #define SER_UART1_BUS_TXINIT do { \
-                               PIOB_PDR = BV(RXD1) | BV(TXD1); \
-                       } while (0)
-               #else
-                       #error Unknown CPU
+               #if CPU_ARM_AT91 && !CPU_ARM_SAM7S_LARGE && !CPU_ARM_SAM7X
+                       #warning Check USART1 pins!
                #endif
+               #define SER_UART1_BUS_TXINIT do { \
+                       PIOA_PDR = BV(RXD1) | BV(TXD1); \
+                       PIO_PERIPH_SEL(PIOA_BASE, BV(RXD1) | BV(TXD1), USART1_PERIPH); \
+               } while (0)
        #endif
 
        #ifndef SER_UART1_BUS_TXBEGIN
@@ -182,13 +176,12 @@
        * Default TXINIT macro - invoked in spi_init()
        * The default is no action.
        */
-       #if CPU_CM3_AT91SAM3
+       #if CPU_CM3_SAM3
                #define SER_SPI0_BUS_TXINIT do { \
                        /* Disable PIO on SPI pins */ \
                        PIOA_PDR = BV(SPI0_SPCK) | BV(SPI0_MOSI) | BV(SPI0_MISO); \
-                       /* PIO is peripheral A */ \
-                       PIOA_ABCDSR1 &= ~(BV(SPI0_SPCK) | BV(SPI0_MOSI) | BV(SPI0_MISO)); \
-                       PIOA_ABCDSR2 &= ~(BV(SPI0_SPCK) | BV(SPI0_MOSI) | BV(SPI0_MISO)); \
+                       /* SPI is peripheral A on SAM3X,A,N,S,U */ \
+                       PIO_PERIPH_SEL(PIOA_BASE, BV(SPI0_SPCK) | BV(SPI0_MOSI) | BV(SPI0_MISO), PIO_PERIPH_A); \
                } while (0)
        #else
                #define SER_SPI0_BUS_TXINIT do { \
@@ -279,7 +272,7 @@ INLINE void sysirq_setPriority(sysirq_t irq, int prio)
        AIC_EOICR = 0; \
 } while (0)
 
-#elif CPU_CM3_AT91SAM3
+#elif CPU_CM3_SAM3
 
 /** Inform hw that we have served the IRQ */
 #define SER_INT_ACK do { /* nop */ } while (0)
@@ -296,7 +289,7 @@ extern struct Serial *ser_handles[SER_CNT];
 /* TX and RX buffers */
 static unsigned char uart0_txbuffer[CONFIG_UART0_TXBUFSIZE];
 static unsigned char uart0_rxbuffer[CONFIG_UART0_RXBUFSIZE];
-#if !CPU_CM3_AT91SAM3U
+#if USART_PORTS > 1
 static unsigned char uart1_txbuffer[CONFIG_UART1_TXBUFSIZE];
 static unsigned char uart1_rxbuffer[CONFIG_UART1_RXBUFSIZE];
 #endif
@@ -330,7 +323,7 @@ struct ArmSerial
 };
 
 static ISR_PROTO(uart0_irq_dispatcher);
-#if !CPU_CM3_AT91SAM3U
+#if USART_PORTS > 1
 static ISR_PROTO(uart1_irq_dispatcher);
 #endif
 static ISR_PROTO(spi0_irq_handler);
@@ -345,7 +338,7 @@ static void uart0_init(
        UNUSED_ARG(struct Serial *, ser))
 {
        US0_IDR = 0xFFFFFFFF;
-       PMC_PCER = BV(US0_ID);
+       pmc_periphEnable(US0_ID);
 
        /*
         * - Reset USART0
@@ -427,6 +420,9 @@ static void uart0_setparity(UNUSED_ARG(struct SerialHardware *, _hw), int parity
                        ASSERT(0);
        }
 }
+
+#if USART_PORTS > 1
+
 /*
  * Callbacks for USART1
  */
@@ -435,7 +431,7 @@ static void uart1_init(
        UNUSED_ARG(struct Serial *, ser))
 {
        US1_IDR = 0xFFFFFFFF;
-       PMC_PCER = BV(US1_ID);
+       pmc_periphEnable(US1_ID);
 
        /*
         * - Reset USART1
@@ -518,6 +514,8 @@ static void uart1_setparity(UNUSED_ARG(struct SerialHardware *, _hw), int parity
        }
 }
 
+#endif /* USART_PORTS > 1 */
+
 /* SPI driver */
 static void spi0_init(UNUSED_ARG(struct SerialHardware *, _hw), UNUSED_ARG(struct Serial *, ser))
 {
@@ -549,7 +547,7 @@ static void spi0_init(UNUSED_ARG(struct SerialHardware *, _hw), UNUSED_ARG(struc
 
        //sysirq_setPriority(INT_SPI0, SERIRQ_PRIORITY);
        sysirq_setHandler(INT_SPI0, spi0_irq_handler);
-       PMC_PCER = BV(SPI0_ID);
+       pmc_periphEnable(SPI0_ID);
 
        /* Enable SPI */
        SPI0_CR = BV(SPI_SPIEN);
@@ -627,7 +625,7 @@ static void spi1_init(UNUSED_ARG(struct SerialHardware *, _hw), UNUSED_ARG(struc
 
        sysirq_setPriority(INT_SPI1, SERIRQ_PRIORITY);
        sysirq_setHandler(INT_SPI1, spi1_irq_dispatcher);
-       PMC_PCER = BV(SPI1_ID);
+       pmc_periphEnable(SPI1_ID);
 
        /* Enable SPI */
        SPI1_CR = BV(SPI_SPIEN);
@@ -709,6 +707,8 @@ static const struct SerialHardwareVT UART0_VT =
        C99INIT(txSending, tx_sending),
 };
 
+#if USART_PORTS > 1
+
 static const struct SerialHardwareVT UART1_VT =
 {
        C99INIT(init, uart1_init),
@@ -719,6 +719,8 @@ static const struct SerialHardwareVT UART1_VT =
        C99INIT(txSending, tx_sending),
 };
 
+#endif /* USART_PORTS > 1 */
+
 static const struct SerialHardwareVT SPI0_VT =
 {
        C99INIT(init, spi0_init),
@@ -752,6 +754,7 @@ static struct ArmSerial UARTDescs[SER_CNT] =
                },
                C99INIT(sending, false),
        },
+#if USART_PORTS > 1
        {
                C99INIT(hw, /**/) {
                        C99INIT(table, &UART1_VT),
@@ -762,6 +765,7 @@ static struct ArmSerial UARTDescs[SER_CNT] =
                },
                C99INIT(sending, false),
        },
+#endif
 
        {
                C99INIT(hw, /**/) {
@@ -857,6 +861,8 @@ static DECLARE_ISR(uart0_irq_dispatcher)
        SER_INT_ACK;
 }
 
+#if USART_PORTS > 1
+
 /**
  * Serial 1 TX interrupt handler
  */
@@ -920,6 +926,8 @@ static DECLARE_ISR(uart1_irq_dispatcher)
        SER_INT_ACK;
 }
 
+#endif /* USART_PORTS > 1 */
+
 /**
  * SPI0 interrupt handler
  */