lm3s1968-gpio: coding style fixes.

[bertos.git] / examples / lm3s1968 / hw / hw_lcd.h

diff --git a/examples/lm3s1968/hw/hw_lcd.h b/examples/lm3s1968/hw/hw_lcd.h
index 4a6ceb9d163f48a63006c9162b1032c5a6d29494..ed2ede9e251cdc4b3e04d79059c043221fd10b48 100644 (file)
--- a/examples/lm3s1968/hw/hw_lcd.h
+++ b/examples/lm3s1968/hw/hw_lcd.h
@@ -69,11 +69,11 @@
  */
 /* Enter command mode */
 #define LCD_SET_COMMAND() \
-       lm3s_gpio_pin_write(GPIO_PORTH_BASE, GPIO_OLEDDC_PIN, 0)
+       lm3s_gpioPinWrite(GPIO_PORTH_BASE, GPIO_OLEDDC_PIN, 0)
 
 /* Enter data mode */
 #define LCD_SET_DATA() \
-       lm3s_gpio_pin_write(GPIO_PORTH_BASE, GPIO_OLEDDC_PIN, GPIO_OLEDDC_PIN)
+       lm3s_gpioPinWrite(GPIO_PORTH_BASE, GPIO_OLEDDC_PIN, GPIO_OLEDDC_PIN)
 
 /* Send data to the display */
 #define LCD_WRITE(x)   lm3s_ssiWriteFrame(SSI0_BASE, x)
@@ -101,16 +101,16 @@ INLINE void lcd_bus_init(void)
        lm3s_busyWait(512);
 
        /* Configure the SSI0CLK and SSIOTX pins for SSI operation. */
-       lm3s_gpio_pin_config(GPIO_PORTA_BASE, BV(2) | BV(3) | BV(5),
+       lm3s_gpioPinConfig(GPIO_PORTA_BASE, BV(2) | BV(3) | BV(5),
                GPIO_DIR_MODE_HW, GPIO_STRENGTH_8MA, GPIO_PIN_TYPE_STD_WPU);
        /*
         * Configure the GPIO port pin used as a D/C# signal (data/command
         * control) for OLED device, and the port pin used to enable power to
         * the OLED panel.
         */
-       lm3s_gpio_pin_config(GPIO_PORTH_BASE, GPIO_OLEDDC_PIN | GPIO_OLEDEN_PIN,
+       lm3s_gpioPinConfig(GPIO_PORTH_BASE, GPIO_OLEDDC_PIN | GPIO_OLEDEN_PIN,
                GPIO_DIR_MODE_OUT, GPIO_STRENGTH_8MA, GPIO_PIN_TYPE_STD);
-       lm3s_gpio_pin_write(GPIO_PORTH_BASE, GPIO_OLEDDC_PIN | GPIO_OLEDEN_PIN,
+       lm3s_gpioPinWrite(GPIO_PORTH_BASE, GPIO_OLEDDC_PIN | GPIO_OLEDEN_PIN,
                        GPIO_OLEDDC_PIN | GPIO_OLEDEN_PIN);
 
        /* Configure the SSI0 port for master mode */
@@ -120,7 +120,7 @@ INLINE void lcd_bus_init(void)
         * Configure the GPIO port pin used as a D/Cn signal for OLED device,
         * and the port pin used to enable power to the OLED panel.
         */
-       lm3s_gpio_pin_config(GPIO_PORTA_BASE, GPIO_OLEDEN_PIN,
+       lm3s_gpioPinConfig(GPIO_PORTA_BASE, GPIO_OLEDEN_PIN,
                GPIO_DIR_MODE_HW, GPIO_STRENGTH_8MA, GPIO_PIN_TYPE_STD_WPU);
 
        /* Drain the SSI RX FIFO */