X-Git-Url: https://codewiz.org/gitweb?a=blobdiff_plain;f=bertos%2Fcpu%2Favr%2Fdrv%2Fser_avr.c;h=d6de8243dbb27056be9a71158b2d97090bd97da2;hb=32d1445272120a254d77ce8d1af1f527da7a2c17;hp=f4cf42de0d76f526711e333553f1402c96d087fe;hpb=e603425ebb795a273a11c073033544f6a51b9247;p=bertos.git

diff --git a/bertos/cpu/avr/drv/ser_avr.c b/bertos/cpu/avr/drv/ser_avr.c
index f4cf42de..d6de8243 100644
--- a/bertos/cpu/avr/drv/ser_avr.c
+++ b/bertos/cpu/avr/drv/ser_avr.c
@@ -46,6 +46,7 @@
 
 #include <cfg/macros.h> /* DIV_ROUND */
 #include <cfg/debug.h>
+#include <cfg/cfg_arch.h> // ARCH_NIGHTTEST
 
 #include <drv/ser.h>
 #include <drv/ser_p.h>
@@ -453,7 +454,7 @@ static void spi_init(UNUSED_ARG(struct SerialHardware *, _hw), UNUSED_ARG(struct
 	 * - as input but tied high forever!
 	 * This driver set the pin as output.
 	 */
-	#warning SPI SS pin set as output for proper operation, check schematics for possible conflicts.
+	#warning FIXME:SPI SS pin set as output for proper operation, check schematics for possible conflicts.
 	ATOMIC(SPI_DDR |= BV(SPI_SS_BIT));
 
 	ATOMIC(SPI_DDR &= ~BV(SPI_MISO_BIT));
@@ -644,7 +645,7 @@ struct SerialHardware *ser_hw_getdesc(int unit)
 #if CONFIG_SER_HWHANDSHAKE
 
 /// This interrupt is triggered when the CTS line goes high
-SIGNAL(SIG_CTS)
+DECLARE_ISR(SIG_CTS)
 {
 	// Re-enable UDR empty interrupt and TX, then disable CTS interrupt
 	UCSR0B = BV(BIT_RXCIE0) | BV(BIT_UDRIE0) | BV(BIT_RXEN0) | BV(BIT_TXEN0);
@@ -657,7 +658,7 @@ SIGNAL(SIG_CTS)
 /**
  * Serial 0 TX interrupt handler
  */
-SIGNAL(USART0_UDRE_vect)
+DECLARE_ISR(USART0_UDRE_vect)
 {
 	SER_STROBE_ON;
 
@@ -705,7 +706,7 @@ SIGNAL(USART0_UDRE_vect)
  * otherwise we'd stop the serial port with some data
  * still pending in the buffer.
  */
-SIGNAL(SIG_UART0_TRANS)
+DECLARE_ISR(SIG_UART0_TRANS)
 {
 	SER_STROBE_ON;
 
@@ -728,7 +729,7 @@ SIGNAL(SIG_UART0_TRANS)
 /**
  * Serial 1 TX interrupt handler
  */
-SIGNAL(USART1_UDRE_vect)
+DECLARE_ISR(USART1_UDRE_vect)
 {
 	SER_STROBE_ON;
 
@@ -766,7 +767,7 @@ SIGNAL(USART1_UDRE_vect)
  *
  * \sa port 0 TX complete handler.
  */
-SIGNAL(USART1_TX_vect)
+DECLARE_ISR(USART1_TX_vect)
 {
 	SER_STROBE_ON;
 
@@ -801,7 +802,7 @@ SIGNAL(USART1_TX_vect)
  *       RXCIE is cleared.  Unfortunately the RXC flag is read-only
  *       and can't be cleared by code.
  */
-SIGNAL(USART0_RX_vect)
+DECLARE_ISR(USART0_RX_vect)
 {
 	SER_STROBE_ON;
 
@@ -849,9 +850,9 @@ SIGNAL(USART0_RX_vect)
  * is heavily loaded, because an interrupt could be retriggered
  * when executing the handler prologue before RXCIE is disabled.
  *
- * \see SIGNAL(USART1_RX_vect)
+ * \see DECLARE_ISR(USART1_RX_vect)
  */
-SIGNAL(USART1_RX_vect)
+DECLARE_ISR(USART1_RX_vect)
 {
 	SER_STROBE_ON;
 
@@ -892,7 +893,7 @@ SIGNAL(USART1_RX_vect)
 /**
  * SPI interrupt handler
  */
-SIGNAL(SIG_SPI)
+DECLARE_ISR(SIG_SPI)
 {
 	SER_STROBE_ON;