X-Git-Url: https://codewiz.org/gitweb?a=blobdiff_plain;f=cpu%2Farm%2Fdrv%2Fser_at91.c;h=37a4f1b695470b281c1e61188d32159bd5928a3c;hb=1fc31f45bcec8bc23a5924ae5b288439abca8ded;hp=cef4c96fbc74e0cc6f9a2d7053a716ab68dc57e4;hpb=6b98394f8b772c4e4d8784f1b810e7435ffe701a;p=bertos.git

diff --git a/cpu/arm/drv/ser_at91.c b/cpu/arm/drv/ser_at91.c
index cef4c96f..37a4f1b6 100644
--- a/cpu/arm/drv/ser_at91.c
+++ b/cpu/arm/drv/ser_at91.c
@@ -101,17 +101,17 @@
 	 *
 	 * - Disable GPIO on USART0 tx/rx pins
 	 * - Reset USART0
-	 * - Set serial param: mode Normal, 8bit data, 1bit stop
+	 * - Set serial param: mode Normal, 8bit data, 1bit stop, parity none
 	 * - Enable both the receiver and the transmitter
 	 * - Enable only the RX complete interrupt
 	 */
-	#if !CPU_ARM_AT91SAM7S256
+	#if !CPU_ARM_AT91SAM7S256 && !CPU_ARM_AT91SAM7X256
 		#warning Check USART0 pins!
 	#endif
 	#define SER_UART0_BUS_TXINIT do { \
 		PIOA_PDR = BV(RXD0) | BV(TXD0); \
 		US0_CR = BV(US_RSTRX) | BV(US_RSTTX); \
-		US0_MR = US_CHMODE_NORMAL | US_CHRL_8 | US_NBSTOP_1; \
+		US0_MR = US_CHMODE_NORMAL | US_CHRL_8 | US_NBSTOP_1 | US_PAR_NO; \
 		US0_CR = BV(US_RXEN) | BV(US_TXEN); \
 		US0_IER = BV(US_RXRDY); \
 	} while (0)
@@ -173,13 +173,13 @@
 
 #ifndef SER_UART1_BUS_TXINIT
 	/** \sa SER_UART1_BUS_TXINIT */
-	#if !CPU_ARM_AT91SAM7S256
+	#if !CPU_ARM_AT91SAM7S256 && !CPU_ARM_AT91SAM7X256
 		#warning Check USART1 pins!
 	#endif
 	#define SER_UART1_BUS_TXINIT do { \
 		PIOA_PDR = BV(RXD1) | BV(TXD1); \
 		US1_CR = BV(US_RSTRX) | BV(US_RSTTX); \
-		US1_MR = US_CHMODE_NORMAL | US_CHRL_8 | US_NBSTOP_1; \
+		US1_MR = US_CHMODE_NORMAL | US_CHRL_8 | US_NBSTOP_1 | US_PAR_NO; \
 		US1_CR = BV(US_RXEN) | BV(US_TXEN); \
 		US1_IER = BV(US_RXRDY); \
 	} while (0)
@@ -209,7 +209,7 @@
 	} while (0)
 #endif
 
-#if 0
+#ifdef NOT_FOR_ARM_PORT_IT
 /**
  * \name Overridable SPI hooks
  *
@@ -263,7 +263,7 @@ static unsigned char uart0_rxbuffer[CONFIG_UART0_RXBUFSIZE];
 static unsigned char uart1_txbuffer[CONFIG_UART1_TXBUFSIZE];
 static unsigned char uart1_rxbuffer[CONFIG_UART1_RXBUFSIZE];
 
-#if 0
+#ifdef NOT_FOR_ARM_PORT_IT
 static unsigned char spi_txbuffer[CONFIG_SPI_TXBUFSIZE];
 static unsigned char spi_rxbuffer[CONFIG_SPI_RXBUFSIZE];
 #endif
@@ -301,7 +301,7 @@ struct ArmSerial
 struct Serial *ser_uart0 = &ser_handles[SER_UART0];
 struct Serial *ser_uart1 = &ser_handles[SER_UART1];
 
-#if 0
+#ifdef NOT_FOR_ARM_PORT_IT
 struct Serial *ser_spi = &ser_handles[SER_SPI];
 #endif
 
@@ -447,7 +447,7 @@ static void uart1_setparity(UNUSED_ARG(struct SerialHardware *, _hw), int parity
 }
 
 /* SPI driver */
-#if 0
+#ifdef NOT_FOR_ARM_PORT_IT
 static void spi_init(UNUSED_ARG(struct SerialHardware *, _hw), UNUSED_ARG(struct Serial *, ser))
 {
 	/*
@@ -602,7 +602,7 @@ static const struct SerialHardwareVT UART1_VT =
 	C99INIT(txSending, tx_sending),
 };
 
-#if 0
+#ifdef NOT_FOR_ARM_PORT_IT
 static const struct SerialHardwareVT SPI_VT =
 {
 	C99INIT(init, spi_init),
@@ -636,7 +636,7 @@ static struct ArmSerial UARTDescs[SER_CNT] =
 		},
 		C99INIT(sending, false),
 	},
-#if 0
+#ifdef NOT_FOR_ARM_PORT_IT
 	{
 		C99INIT(hw, /**/) {
 			C99INIT(table, &SPI_VT),
@@ -703,18 +703,17 @@ static void uart0_irq_rx(void)
 /**
  * Serial IRQ dispatcher for USART0.
  */
-static void uart0_irq_dispatcher(void) __attribute__ ((naked));
+static void uart0_irq_dispatcher(void) __attribute__ ((interrupt));
 static void uart0_irq_dispatcher(void)
 {
-	IRQ_ENTRY();
-
-	if (US0_IMR & BV(US_RXRDY))
+	if (US0_CSR & BV(US_RXRDY))
 		uart0_irq_rx();
 
-	if (US0_IMR & BV(US_TXRDY))
+	if (US0_CSR & BV(US_TXRDY))
 		uart0_irq_tx();
 
-	IRQ_EXIT();
+	/* Inform hw that we have served the IRQ */
+	AIC_EOICR = 0;
 }
 
 /**
@@ -764,16 +763,15 @@ static void uart1_irq_rx(void)
 /**
  * Serial IRQ dispatcher for USART1.
  */
-static void uart1_irq_dispatcher(void) __attribute__ ((naked));
+static void uart1_irq_dispatcher(void) __attribute__ ((interrupt));
 static void uart1_irq_dispatcher(void)
 {
-	IRQ_ENTRY();
-
-	if (US1_IMR & BV(US_RXRDY))
+	if (US1_CSR & BV(US_RXRDY))
 		uart1_irq_rx();
 
-	if (US1_IMR & BV(US_TXRDY))
+	if (US1_CSR & BV(US_TXRDY))
 		uart1_irq_tx();
 
-	IRQ_EXIT();
+	/* Inform hw that we have served the IRQ */
+	AIC_EOICR = 0;
 }