X-Git-Url: https://codewiz.org/gitweb?a=blobdiff_plain;f=drv%2Fser_avr.c;h=23c4b0760d7f6be343da5843a22caa71b2b66503;hb=HEAD;hp=55665a40acb333ae048b14b9bc9ac314229c676b;hpb=5b25ae54d86d894e5d01adeef10938df1bb10e16;p=bertos.git diff --git a/drv/ser_avr.c b/drv/ser_avr.c deleted file mode 100755 index 55665a40..00000000 --- a/drv/ser_avr.c +++ /dev/null @@ -1,854 +0,0 @@ -/*! - * \file - * - * - * \brief AVR UART and SPI I/O driver - * - * Rationale for project_ks hardware. - * - * The serial 0 on the board_kf board is used to communicate with the - * smart card, which has the TX and RX lines connected together. To - * allow the smart card to drive the RX line of the CPU the CPU TX has - * to be in a high impedance state. - * Whenever a transmission is done and there is nothing more to send - * the transmitter is turn off. The output pin is held in input with - * pull-up enabled, to avoid capturing noise from the nearby RX line. - * - * The line on the KBus port must keep sending data, even when - * there is nothing to transmit, because a burst data transfer - * generates noise on the audio channels. - * This is accomplished using the multiprocessor mode of the - * ATmega64/128 serial. - * - * The receiver keeps the MPCM bit always on. When useful data - * is trasmitted the address bit is set. The receiver hardware - * consider the frame as address info and receive it. - * When useless fill bytes are sent the address bit is cleared - * and the receiver will ignore them, avoiding useless triggering - * of RXC interrupt. - * - * \version $Id$ - * \author Bernardo Innocenti - * \author Stefano Fedrigo - */ - -/*#* - *#* $Log$ - *#* Revision 1.19 2004/12/13 11:51:08 bernie - *#* DISABLE_INTS/ENABLE_INTS: Convert to IRQ_DISABLE/IRQ_ENABLE. - *#* - *#* Revision 1.18 2004/12/08 08:03:48 bernie - *#* Doxygen fixes. - *#* - *#* Revision 1.17 2004/10/19 07:52:35 bernie - *#* Reset parity bits before overwriting them (Fixed by batt in project_ks). - *#* - *#* Revision 1.16 2004/10/03 18:45:48 bernie - *#* Convert to new-style config macros; Allow compiling with a C++ compiler (mostly). - *#* - *#* Revision 1.15 2004/09/14 21:05:36 bernie - *#* Use debug.h instead of kdebug.h; Use new AVR pin names; Spelling fixes. - *#* - *#* Revision 1.14 2004/09/06 21:50:00 bernie - *#* Spelling fixes. - *#* - *#* Revision 1.13 2004/09/06 21:40:50 bernie - *#* Move buffer handling in chip-specific driver. - *#* - *#* Revision 1.12 2004/08/29 22:06:10 bernie - *#* Fix a bug in the (unused) RTS/CTS code; Clarify documentation. - *#* - *#* Revision 1.10 2004/08/10 06:30:41 bernie - *#* Major redesign of serial bus policy handling. - *#* - *#* Revision 1.9 2004/08/02 20:20:29 aleph - *#* Merge from project_ks - *#* - *#* Revision 1.8 2004/07/29 22:57:09 bernie - *#* Several tweaks to reduce code size on ATmega8. - *#* - *#* Revision 1.7 2004/07/18 21:54:23 bernie - *#* Add ATmega8 support. - *#* - *#* Revision 1.5 2004/06/27 15:25:40 aleph - *#* Add missing callbacks for SPI; - *#* Change UNUSED() macro to new version with two args; - *#* Use TX line filling only on the correct KBUS serial port; - *#* Fix nasty IRQ disabling bug in recv complete hander for port 1. - *#* - *#* Revision 1.4 2004/06/03 11:27:09 bernie - *#* Add dual-license information. - *#* - *#* Revision 1.3 2004/06/02 21:35:24 aleph - *#* Serial enhancements: interruptible receive handler and 8 bit serial status for AVR; remove volatile attribute to FIFOBuffer, useless for new fifobuf routens - *#* - *#* Revision 1.2 2004/05/23 18:21:53 bernie - *#* Trim CVS logs and cleanup header info. - *#* - *#*/ - -#include "ser.h" -#include "ser_p.h" -#include "config.h" -#include "hw.h" /* Required for bus macros overrides */ - -#include -#include -#include - -#include -#include - - -/*! - * \name Hardware handshake (RTS/CTS). - * \{ - */ -#ifndef RTS_ON -#define RTS_ON do {} while (0) -#endif -#ifndef RTS_OFF -#define RTS_OFF do {} while (0) -#endif -#ifndef IS_CTS_ON -#define IS_CTS_ON true -#endif -#ifndef EIMSKB_CTS -#define EIMSKB_CTS 0 /*!< Dummy value, must be overridden */ -#endif -/*\}*/ - - -/*! - * \name Overridable serial bus hooks - * - * These can be redefined in hw.h to implement - * special bus policies such as half-duplex, 485, etc. - * - * - * \code - * TXBEGIN TXCHAR TXEND TXOFF - * | __________|__________ | | - * | | | | | | | | | - * v v v v v v v v v - * ______ __ __ __ __ __ __ ________________ - * \/ \/ \/ \/ \/ \/ \/ - * ______/\__/\__/\__/\__/\__/\__/ - * - * \endcode - * - * \{ - */ -#ifndef SER_UART0_BUS_TXINIT - /*! - * Default TXINIT macro - invoked in uart0_init() - * - * - Enable both the receiver and the transmitter - * - Enable only the RX complete interrupt - */ - #define SER_UART0_BUS_TXINIT do { \ - UCSR0B = BV(RXCIE) | BV(RXEN) | BV(TXEN); \ - } while (0) -#endif - -#ifndef SER_UART0_BUS_TXBEGIN - /*! - * Invoked before starting a transmission - * - * - Enable both the receiver and the transmitter - * - Enable both the RX complete and UDR empty interrupts - */ - #define SER_UART0_BUS_TXBEGIN do { \ - UCSR0B = BV(RXCIE) | BV(UDRIE) | BV(RXEN) | BV(TXEN); \ - } while (0) -#endif - -#ifndef SER_UART0_BUS_TXCHAR - /*! - * Invoked to send one character. - */ - #define SER_UART0_BUS_TXCHAR(c) do { \ - UDR0 = (c); \ - } while (0) -#endif - -#ifndef SER_UART0_BUS_TXEND - /*! - * Invoked as soon as the txfifo becomes empty - * - * - Keep both the receiver and the transmitter enabled - * - Keep the RX complete interrupt enabled - * - Disable the UDR empty interrupt - */ - #define SER_UART0_BUS_TXEND do { \ - UCSR0B = BV(RXCIE) | BV(RXEN) | BV(TXEN); \ - } while (0) -#endif - -#ifndef SER_UART0_BUS_TXOFF - /*! - * \def SER_UART0_BUS_TXOFF - * - * Invoked after the last character has been transmitted - * - * The default is no action. - */ - #ifdef __doxygen__ - #define SER_UART0_BUS_TXOFF - #endif -#endif - -#ifndef SER_UART1_BUS_TXINIT - /*! \sa SER_UART0_BUS_TXINIT */ - #define SER_UART1_BUS_TXINIT do { \ - UCSR1B = BV(RXCIE) | BV(RXEN) | BV(TXEN); \ - } while (0) -#endif -#ifndef SER_UART1_BUS_TXBEGIN - /*! \sa SER_UART0_BUS_TXBEGIN */ - #define SER_UART1_BUS_TXBEGIN do { \ - UCSR1B = BV(RXCIE) | BV(UDRIE) | BV(RXEN) | BV(TXEN); \ - } while (0) -#endif -#ifndef SER_UART1_BUS_TXCHAR - /*! \sa SER_UART0_BUS_TXCHAR */ - #define SER_UART1_BUS_TXCHAR(c) do { \ - UDR1 = (c); \ - } while (0) -#endif -#ifndef SER_UART1_BUS_TXEND - /*! \sa SER_UART0_BUS_TXEND */ - #define SER_UART1_BUS_TXEND do { \ - UCSR1B = BV(RXCIE) | BV(RXEN) | BV(TXEN); \ - } while (0) -#endif -#ifndef SER_UART1_BUS_TXOFF - /*! - * \def SER_UART1_BUS_TXOFF - * - * \see SER_UART0_BUS_TXOFF - */ - #ifdef __doxygen__ - #define SER_UART1_BUS_TXOFF - #endif -#endif -/*\}*/ - - -/* SPI port and pin configuration */ -#define SPI_PORT PORTB -#define SPI_DDR DDRB -#define SPI_SCK_BIT PB1 -#define SPI_MOSI_BIT PB2 -#define SPI_MISO_BIT PB3 - -/* USART register definitions */ -#if CPU_AVR_ATMEGA64 || CPU_AVR_ATMEGA128 - #define AVR_HAS_UART1 1 -#elif CPU_AVR_ATMEGA8 - #define AVR_HAS_UART1 0 - #define UCSR0A UCSRA - #define UCSR0B UCSRB - #define UCSR0C UCSRC - #define UDR0 UDR - #define UBRR0L UBRRL - #define UBRR0H UBRRH - #define SIG_UART0_DATA SIG_UART_DATA - #define SIG_UART0_RECV SIG_UART_RECV -#elif CPU_AVR_ATMEGA103 - #define AVR_HAS_UART1 0 - #define UCSR0B UCR - #define UDR0 UDR - #define UCSR0A USR - #define UBRR0L UBRR - #define SIG_UART0_DATA SIG_UART_DATA - #define SIG_UART0_RECV SIG_UART_RECV -#else - #error Unknown architecture -#endif - - -/*! - * \def CONFIG_SER_STROBE - * - * This is a debug facility that can be used to - * monitor SER interrupt activity on an external pin. - * - * To use strobes, redefine the macros SER_STROBE_ON, - * SER_STROBE_OFF and SER_STROBE_INIT and set - * CONFIG_SER_STROBE to 1. - */ -#if !defined(CONFIG_SER_STROBE) || !CONFIG_SER_STROBE - #define SER_STROBE_ON do {/*nop*/} while(0) - #define SER_STROBE_OFF do {/*nop*/} while(0) - #define SER_STROBE_INIT do {/*nop*/} while(0) -#endif - - -/* From the high-level serial driver */ -extern struct Serial ser_handles[SER_CNT]; - -/* TX and RX buffers */ -static unsigned char uart0_txbuffer[CONFIG_UART0_TXBUFSIZE]; -static unsigned char uart0_rxbuffer[CONFIG_UART0_RXBUFSIZE]; -#if AVR_HAS_UART1 - static unsigned char uart1_txbuffer[CONFIG_UART1_TXBUFSIZE]; - static unsigned char uart1_rxbuffer[CONFIG_UART1_RXBUFSIZE]; -#endif -static unsigned char spi_txbuffer[CONFIG_SPI_TXBUFSIZE]; -static unsigned char spi_rxbuffer[CONFIG_SPI_RXBUFSIZE]; - - -/*! - * Internal hardware state structure - * - * The \a sending variable is true while the transmission - * interrupt is retriggering itself. - * - * For the USARTs the \a sending flag is useful for taking specific - * actions before sending a burst of data, at the start of a trasmission - * but not before every char sent. - * - * For the SPI, this flag is necessary because the SPI sends and receives - * bytes at the same time and the SPI IRQ is unique for send/receive. - * The only way to start transmission is to write data in SPDR (this - * is done by spi_starttx()). We do this *only* if a transfer is - * not already started. - */ -struct AvrSerial -{ - struct SerialHardware hw; - volatile bool sending; -}; - - -/* - * These are to trick GCC into *not* using absolute addressing mode - * when accessing ser_handles, which is very expensive. - * - * Accessing through these pointers generates much shorter - * (and hopefully faster) code. - */ -struct Serial *ser_uart0 = &ser_handles[SER_UART0]; -#if AVR_HAS_UART1 -struct Serial *ser_uart1 = &ser_handles[SER_UART1]; -#endif -struct Serial *ser_spi = &ser_handles[SER_SPI]; - - - -/* - * Callbacks - */ -static void uart0_init(UNUSED(struct SerialHardware *, _hw), UNUSED(struct Serial *, ser)) -{ - SER_UART0_BUS_TXINIT; - RTS_ON; -} - -static void uart0_cleanup(UNUSED(struct SerialHardware *, _hw)) -{ - UCSR0B = 0; -} - -static void uart0_enabletxirq(struct SerialHardware *_hw) -{ - struct AvrSerial *hw = (struct AvrSerial *)_hw; - - /* - * WARNING: racy code here! The tx interrupt sets hw->sending to false - * when it runs with an empty fifo. The order of statements in the - * if-block matters. - */ - if (!hw->sending) - { - hw->sending = true; - SER_UART0_BUS_TXBEGIN; - } -} - -static void uart0_setbaudrate(UNUSED(struct SerialHardware *, _hw), unsigned long rate) -{ - /* Compute baud-rate period */ - uint16_t period = (((CLOCK_FREQ / 16UL) + (rate / 2)) / rate) - 1; - -#ifndef __AVR_ATmega103__ - UBRR0H = (period) >> 8; -#endif - UBRR0L = (period); - - //DB(kprintf("uart0_setbaudrate(rate=%lu): period=%d\n", rate, period);) -} - -static void uart0_setparity(UNUSED(struct SerialHardware *, _hw), int parity) -{ -#if !CPU_AVR_ATMEGA103 - UCSR0C = (UCSR0C & ~(BV(UPM1) | BV(UPM0))) | ((parity) << UPM0); -#endif -} - -#if AVR_HAS_UART1 - -static void uart1_init(UNUSED(struct SerialHardware *, _hw), UNUSED(struct Serial *, ser)) -{ - SER_UART1_BUS_TXINIT; - RTS_ON; - SER_STROBE_INIT; -} - -static void uart1_cleanup(UNUSED(struct SerialHardware *, _hw)) -{ - UCSR1B = 0; -} - -static void uart1_enabletxirq(struct SerialHardware *_hw) -{ - struct AvrSerial *hw = (struct AvrSerial *)_hw; - - /* - * WARNING: racy code here! The tx interrupt - * sets hw->sending to false when it runs with - * an empty fifo. The order of the statements - * in the if-block matters. - */ - if (!hw->sending) - { - hw->sending = true; - SER_UART1_BUS_TXBEGIN; - } -} - -static void uart1_setbaudrate(UNUSED(struct SerialHardware *, _hw), unsigned long rate) -{ - /* Compute baud-rate period */ - uint16_t period = (((CLOCK_FREQ / 16UL) + (rate / 2)) / rate) - 1; - - UBRR1H = (period) >> 8; - UBRR1L = (period); - - //DB(kprintf("uart1_setbaudrate(rate=%ld): period=%d\n", rate, period);) -} - -static void uart1_setparity(UNUSED(struct SerialHardware *, _hw), int parity) -{ - UCSR1C = (UCSR1C & ~(BV(UPM1) | BV(UPM0))) | ((parity) << UPM0); -} - -#endif // AVR_HAS_UART1 - -static void spi_init(UNUSED(struct SerialHardware *, _hw), UNUSED(struct Serial *, ser)) -{ - /* - * Set MOSI and SCK ports out, MISO in. - * - * The ATmega64/128 datasheet explicitly states that the input/output - * state of the SPI pins is not significant, as when the SPI is - * active the I/O port are overrided. - * This is *blatantly FALSE*. - * - * Moreover, the MISO pin on the board_kc *must* be in high impedance - * state even when the SPI is off, because the line is wired together - * with the KBus serial RX, and the transmitter of the slave boards - * would be unable to drive the line. - */ - SPI_DDR |= BV(SPI_MOSI_BIT) | BV(SPI_SCK_BIT); - SPI_DDR &= ~BV(SPI_MISO_BIT); - /* Enable SPI, IRQ on, Master, CPU_CLOCK/16 */ - SPCR = BV(SPE) | BV(SPIE) | BV(MSTR) | BV(SPR0); -} - -static void spi_cleanup(UNUSED(struct SerialHardware *, _hw)) -{ - SPCR = 0; - /* Set all pins as inputs */ - SPI_DDR &= ~(BV(SPI_MISO_BIT) | BV(SPI_MOSI_BIT) | BV(SPI_SCK_BIT)); -} - -static void spi_starttx(struct SerialHardware *_hw) -{ - struct AvrSerial *hw = (struct AvrSerial *)_hw; - - cpuflags_t flags; - DISABLE_IRQSAVE(flags); - - /* Send data only if the SPI is not already transmitting */ - if (!hw->sending && !fifo_isempty(&ser_spi->txfifo)) - { - hw->sending = true; - SPDR = fifo_pop(&ser_spi->txfifo); - } - - ENABLE_IRQRESTORE(flags); -} - -static void spi_setbaudrate(UNUSED(struct SerialHardware *, _hw), UNUSED(unsigned long, rate)) -{ - // nop -} - -static void spi_setparity(UNUSED(struct SerialHardware *, _hw), UNUSED(int, parity)) -{ - // nop -} - - -// FIXME: move into compiler.h? Ditch? -#if COMPILER_C99 - #define C99INIT(name,val) .name = val -#elif defined(__GNUC__) - #define C99INIT(name,val) name: val -#else - #warning No designated initializers, double check your code - #define C99INIT(name,val) (val) -#endif - -/* - * High-level interface data structures - */ -static const struct SerialHardwareVT UART0_VT = -{ - C99INIT(init, uart0_init), - C99INIT(cleanup, uart0_cleanup), - C99INIT(setbaudrate, uart0_setbaudrate), - C99INIT(setparity, uart0_setparity), - C99INIT(enabletxirq, uart0_enabletxirq), -}; - -#if AVR_HAS_UART1 -static const struct SerialHardwareVT UART1_VT = -{ - C99INIT(init, uart1_init), - C99INIT(cleanup, uart1_cleanup), - C99INIT(setbaudrate, uart1_setbaudrate), - C99INIT(setparity, uart1_setparity), - C99INIT(enabletxirq, uart1_enabletxirq), -}; -#endif // AVR_HAS_UART1 - -static const struct SerialHardwareVT SPI_VT = -{ - C99INIT(init, spi_init), - C99INIT(cleanup, spi_cleanup), - C99INIT(setbaudrate, spi_setbaudrate), - C99INIT(setparity, spi_setparity), - C99INIT(enabletxirq, spi_starttx), -}; - -static struct AvrSerial UARTDescs[SER_CNT] = -{ - { - C99INIT(hw, /**/) { - C99INIT(table, &UART0_VT), - C99INIT(txbuffer, uart0_txbuffer), - C99INIT(rxbuffer, uart0_rxbuffer), - C99INIT(txbuffer_size, sizeof(uart0_txbuffer)), - C99INIT(rxbuffer_size, sizeof(uart0_rxbuffer)), - }, - C99INIT(sending, false), - }, -#if AVR_HAS_UART1 - { - C99INIT(hw, /**/) { - C99INIT(table, &UART1_VT), - C99INIT(txbuffer, uart1_txbuffer), - C99INIT(rxbuffer, uart1_rxbuffer), - C99INIT(txbuffer_size, sizeof(uart1_txbuffer)), - C99INIT(rxbuffer_size, sizeof(uart1_rxbuffer)), - }, - C99INIT(sending, false), - }, -#endif - { - C99INIT(hw, /**/) { - C99INIT(table, &SPI_VT), - C99INIT(txbuffer, spi_txbuffer), - C99INIT(rxbuffer, spi_rxbuffer), - C99INIT(txbuffer_size, sizeof(spi_txbuffer)), - C99INIT(rxbuffer_size, sizeof(spi_rxbuffer)), - }, - C99INIT(sending, false), - } -}; - -struct SerialHardware* ser_hw_getdesc(int unit) -{ - ASSERT(unit < SER_CNT); - return &UARTDescs[unit].hw; -} - - -/* - * Interrupt handlers - */ - -#if CONFIG_SER_HWHANDSHAKE - -//! This interrupt is triggered when the CTS line goes high -SIGNAL(SIG_CTS) -{ - // Re-enable UDR empty interrupt and TX, then disable CTS interrupt - UCSR0B = BV(RXCIE) | BV(UDRIE) | BV(RXEN) | BV(TXEN); - cbi(EIMSK, EIMSKB_CTS); -} - -#endif // CONFIG_SER_HWHANDSHAKE - - -/*! - * Serial 0 TX interrupt handler - */ -SIGNAL(SIG_UART0_DATA) -{ - SER_STROBE_ON; - - struct FIFOBuffer * const txfifo = &ser_uart0->txfifo; - - if (fifo_isempty(txfifo)) - { - SER_UART0_BUS_TXEND; -#ifndef SER_UART0_BUS_TXOFF - UARTDescs[SER_UART0].sending = false; -#endif - } -#if CPU_AVR_ATMEGA64 || CPU_AVR_ATMEGA128 || CPU_AVR_ATMEGA103 - else if (!IS_CTS_ON) - { - // Disable rx interrupt and tx, enable CTS interrupt - // UNTESTED - UCSR0B = BV(RXCIE) | BV(RXEN) | BV(TXEN); - sbi(EIFR, EIMSKB_CTS); - sbi(EIMSK, EIMSKB_CTS); - } -#endif - else - { - char c = fifo_pop(txfifo); - SER_UART0_BUS_TXCHAR(c); - } - - SER_STROBE_OFF; -} - -#ifdef SER_UART0_BUS_TXOFF -/*! - * Serial port 0 TX complete interrupt handler. - * - * This IRQ is usually disabled. The UDR-empty interrupt - * enables it when there's no more data to transmit. - * We need to wait until the last character has been - * transmitted before switching the 485 transceiver to - * receive mode. - * - * The txfifo might have been refilled by putchar() while - * we were waiting for the transmission complete interrupt. - * In this case, we must restart the UDR empty interrupt, - * otherwise we'd stop the serial port with some data - * still pending in the buffer. - */ -SIGNAL(SIG_UART0_TRANS) -{ - SER_STROBE_ON; - - struct FIFOBuffer * const txfifo = &ser_uart0->txfifo; - if (fifo_isempty(txfifo)) - { - SER_UART0_BUS_TXOFF; - UARTDescs[SER_UART0].sending = false; - } - else - UCSR0B = BV(RXCIE) | BV(UDRIE) | BV(RXEN) | BV(TXEN); - - SER_STROBE_OFF; -} -#endif /* SER_UART0_BUS_TXOFF */ - - -#if AVR_HAS_UART1 - -/*! - * Serial 1 TX interrupt handler - */ -SIGNAL(SIG_UART1_DATA) -{ - SER_STROBE_ON; - - struct FIFOBuffer * const txfifo = &ser_uart1->txfifo; - - if (fifo_isempty(txfifo)) - { - SER_UART1_BUS_TXEND; -#ifndef SER_UART1_BUS_TXOFF - UARTDescs[SER_UART1].sending = false; -#endif - } -#if CPU_AVR_ATMEGA64 || CPU_AVR_ATMEGA128 || CPU_AVR_ATMEGA103 - else if (!IS_CTS_ON) - { - // Disable rx interrupt and tx, enable CTS interrupt - // UNTESTED - UCSR1B = BV(RXCIE) | BV(RXEN) | BV(TXEN); - sbi(EIFR, EIMSKB_CTS); - sbi(EIMSK, EIMSKB_CTS); - } -#endif - else - { - char c = fifo_pop(txfifo); - SER_UART1_BUS_TXCHAR(c); - } - - SER_STROBE_OFF; -} - -#ifdef SER_UART1_BUS_TXOFF -/*! - * Serial port 1 TX complete interrupt handler. - * - * \sa port 0 TX complete handler. - */ -SIGNAL(SIG_UART1_TRANS) -{ - SER_STROBE_ON; - - struct FIFOBuffer * const txfifo = &ser_uart1->txfifo; - if (fifo_isempty(txfifo)) - { - SER_UART1_BUS_TXOFF; - UARTDescs[SER_UART1].sending = false; - } - else - UCSR1B = BV(RXCIE) | BV(UDRIE) | BV(RXEN) | BV(TXEN); - - SER_STROBE_OFF; -} -#endif /* SER_UART1_BUS_TXOFF */ - -#endif // AVR_HAS_UART1 - - -/*! - * Serial 0 RX complete interrupt handler. - * - * This handler is interruptible. - * Interrupt are reenabled as soon as recv complete interrupt is - * disabled. Using INTERRUPT() is troublesome when the serial - * is heavily loaded, because an interrupt could be retriggered - * when executing the handler prologue before RXCIE is disabled. - * - * \note The code that re-enables interrupts is commented out - * because in some nasty cases the interrupt is retriggered. - * This is probably due to the RXC flag being set before - * RXCIE is cleared. Unfortunately the RXC flag is read-only - * and can't be cleared by code. - */ -SIGNAL(SIG_UART0_RECV) -{ - SER_STROBE_ON; - - /* Disable Recv complete IRQ */ - //UCSR0B &= ~BV(RXCIE); - //IRQ_ENABLE; - - /* Should be read before UDR */ - ser_uart0->status |= UCSR0A & (SERRF_RXSROVERRUN | SERRF_FRAMEERROR); - - /* To clear the RXC flag we must _always_ read the UDR even when we're - * not going to accept the incoming data, otherwise a new interrupt - * will occur once the handler terminates. - */ - char c = UDR0; - struct FIFOBuffer * const rxfifo = &ser_uart0->rxfifo; - - if (fifo_isfull(rxfifo)) - ser_uart0->status |= SERRF_RXFIFOOVERRUN; - else - { - fifo_push(rxfifo, c); -#if CONFIG_SER_HWHANDSHAKE - if (fifo_isfull(rxfifo)) - RTS_OFF; -#endif - } - - /* Reenable receive complete int */ - //IRQ_DISABLE; - //UCSR0B |= BV(RXCIE); - - SER_STROBE_OFF; -} - - -#if AVR_HAS_UART1 - -/*! - * Serial 1 RX complete interrupt handler. - * - * This handler is interruptible. - * Interrupt are reenabled as soon as recv complete interrupt is - * disabled. Using INTERRUPT() is troublesome when the serial - * is heavily loaded, because an interrupt could be retriggered - * when executing the handler prologue before RXCIE is disabled. - * - * \see SIGNAL(SIG_UART0_RECV) - */ -SIGNAL(SIG_UART1_RECV) -{ - SER_STROBE_ON; - - /* Disable Recv complete IRQ */ - //UCSR1B &= ~BV(RXCIE); - //IRQ_ENABLE; - - /* Should be read before UDR */ - ser_uart1->status |= UCSR1A & (SERRF_RXSROVERRUN | SERRF_FRAMEERROR); - - /* To avoid an IRQ storm, we must _always_ read the UDR even when we're - * not going to accept the incoming data - */ - char c = UDR1; - struct FIFOBuffer * const rxfifo = &ser_uart1->rxfifo; - //ASSERT_VALID_FIFO(rxfifo); - - if (UNLIKELY(fifo_isfull(rxfifo))) - ser_uart1->status |= SERRF_RXFIFOOVERRUN; - else - { - fifo_push(rxfifo, c); -#if CONFIG_SER_HWHANDSHAKE - if (fifo_isfull(rxfifo)) - RTS_OFF; -#endif - } - /* Re-enable receive complete int */ - //UCSR1B |= BV(RXCIE); - - SER_STROBE_OFF; -} - -#endif // AVR_HAS_UART1 - - -/*! - * SPI interrupt handler - */ -SIGNAL(SIG_SPI) -{ - /* Read incoming byte. */ - if (!fifo_isfull(&ser_spi->rxfifo)) - fifo_push(&ser_spi->rxfifo, SPDR); - /* - * FIXME - else - ser_spi->status |= SERRF_RXFIFOOVERRUN; - */ - - /* Send */ - if (!fifo_isempty(&ser_spi->txfifo)) - SPDR = fifo_pop(&ser_spi->txfifo); - else - UARTDescs[SER_SPI].sending = false; -}