Bugfixes for DSP56K serial driver from scfirm.

git-svn-id: https://src.develer.com/svnoss/bertos/trunk@248 38d2e660-2303-0410-9eaa-f027e97ec537

diff --git a/drv/ser_dsp56k.c b/drv/ser_dsp56k.c
index dccc806ae47105549c3bd0c8e76d9940f7c03827..efdb2e2bcc0a899526736d6782266fde753f02d6 100755 (executable)
--- a/drv/ser_dsp56k.c
+++ b/drv/ser_dsp56k.c
@@ -1,7 +1,7 @@
 /*!
  * \file
  * <!--
- * Copyright (C) 2003,2004 Develer S.r.l. (http://www.develer.com/)
+ * Copyright 2003, 2004 Develer S.r.l. (http://www.develer.com/)
  * This file is part of DevLib - See devlib/README for information.
  * -->
  *
@@ -15,8 +15,8 @@
 
 /*#*
  *#* $Log$
- *#* Revision 1.6  2004/10/03 20:43:22  bernie
- *#* Import changes from sc/firmware.
+ *#* Revision 1.7  2004/10/19 08:57:15  bernie
+ *#* Bugfixes for DSP56K serial driver from scfirm.
  *#*
  *#* Revision 1.5  2004/08/25 14:12:08  rasky
  *#* Aggiornato il comment block dei log RCS
@@ -51,6 +51,11 @@
        #error error flags do not match with register bits
 #endif
 
+static unsigned char ser0_fifo_rx[CONFIG_SER0_FIFOSIZE_RX];
+static unsigned char ser0_fifo_tx[CONFIG_SER0_FIFOSIZE_TX];
+static unsigned char ser1_fifo_rx[CONFIG_SER1_FIFOSIZE_RX];
+static unsigned char ser1_fifo_tx[CONFIG_SER1_FIFOSIZE_TX];
+
 struct SCI
 {
        struct SerialHardware hw;
@@ -67,7 +72,7 @@ static inline void enable_tx_irq_bare(volatile struct REG_SCI_STRUCT* regs)
 
 static inline void enable_rx_irq_bare(volatile struct REG_SCI_STRUCT* regs)
 {
-       regs->CR |= REG_SCI_CR_RIE | REG_SCI_CR_REIE;
+       regs->CR |= REG_SCI_CR_RIE;
 }
 
 static inline void disable_tx_irq_bare(volatile struct REG_SCI_STRUCT* regs)
@@ -124,18 +129,29 @@ static void rx_isr(const struct SCI *hw)
 #pragma interrupt warn
        volatile struct REG_SCI_STRUCT* regs = hw->regs;
 
+       // Propagate errors
        hw->serial->status |= regs->SR & (SERRF_PARITYERROR |
                                          SERRF_RXSROVERRUN |
                                          SERRF_FRAMEERROR |
                                          SERRF_NOISEERROR);
 
+       /*
+        * Serial IRQ can happen for two reason: data ready (RDRF) or overrun (OR)
+        * If the data is ready, we need to fetch it from the data register or
+        * the interrupt will retrigger immediatly. In case of overrun, instead,
+        * the value of the data register is meaningless.
+        */
+       if (regs->SR & REG_SCI_SR_RDRF)
+       {
+               unsigned char data = regs->DR;
+
+               if (fifo_isfull(&hw->serial->rxfifo))
        if (fifo_isfull(&hw->serial->rxfifo))
                hw->serial->status |= SERRF_RXFIFOOVERRUN;
        else
                fifo_push(&hw->serial->rxfifo, regs->DR);
 
-       // Writing anything to the status register clear the
-       //  error bits.
+       // Writing anything to the status register clear the error bits.
        regs->SR = 0;
 }
 
@@ -202,14 +218,28 @@ static const struct SerialHardwareVT SCI_VT =
 static struct SCI SCIDescs[2] =
 {
        {
-               .hw = { .table = &SCI_VT },
+               .hw =
+               {
+                       .table = &SCI_VT,
+                       .rxbuffer = ser0_fifo_rx,
+                       .txbuffer = ser0_fifo_tx,
+                       .rxbuffer_size = countof(ser0_fifo_rx),
+                       .txbuffer_size = countof(ser0_fifo_tx),
+               },
                .regs = &REG_SCI[0],
                .irq_rx = IRQ_SCI0_RECEIVER_FULL,
                .irq_tx = IRQ_SCI0_TRANSMITTER_READY,
        },
 
        {
-               .hw = { .table = &SCI_VT },
+               .hw =
+               {
+                       .table = &SCI_VT,
+                       .rxbuffer = ser1_fifo_rx,
+                       .txbuffer = ser1_fifo_tx,
+                       .rxbuffer_size = countof(ser1_fifo_rx),
+                       .txbuffer_size = countof(ser1_fifo_tx),
+               },
                .regs = &REG_SCI[1],
                .irq_rx = IRQ_SCI1_RECEIVER_FULL,
                .irq_tx = IRQ_SCI1_TRANSMITTER_READY,