--- /dev/null
+/**
+ * \file
+ * <!--
+ * This file is part of BeRTOS.
+ *
+ * Bertos is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ *
+ * As a special exception, you may use this file as part of a free software
+ * library without restriction. Specifically, if other files instantiate
+ * templates or use macros or inline functions from this file, or you compile
+ * this file and link it with other files to produce an executable, this
+ * file does not by itself cause the resulting executable to be covered by
+ * the GNU General Public License. This exception does not however
+ * invalidate any other reasons why the executable file might be covered by
+ * the GNU General Public License.
+ *
+ * Copyright 2008 Develer S.r.l. (http://www.develer.com/)
+ * All Rights Reserved.
+ * -->
+ *
+ * \brief Configuration file for serial module.
+ *
+ * \version $Id$
+ *
+ * \author Daniele Basile <asterix@develer.com>
+ */
+
+#ifndef CFG_SER_H
+#define CFG_SER_H
+
+
+/// Kdebug console on debug unit
+#define CONFIG_TRIFACE_PORT 0
+
+/// Baud-rate for the kdebug console
+#define CONFIG_TRIFACE_BAUDRATE 115200
+
+/// [bytes] Size of the outbound FIFO buffer for port 0.
+#define CONFIG_UART0_TXBUFSIZE 32
+
+/// [bytes] Size of the inbound FIFO buffer for port 0.
+#define CONFIG_UART0_RXBUFSIZE 64
+
+/// [bytes] Size of the outbound FIFO buffer for port 1.
+#define CONFIG_UART1_TXBUFSIZE 32
+
+/// [bytes] Size of the inbound FIFO buffer for port 1.
+#define CONFIG_UART1_RXBUFSIZE 64
+
+
+/// [bytes] Size of the outbound FIFO buffer for SPI port (AVR only)
+#define CONFIG_SPI_TXBUFSIZE 32
+
+/// [bytes] Size of the inbound FIFO buffer for SPI port (AVR only)
+#define CONFIG_SPI_RXBUFSIZE 32
+
+/// [bytes] Size of the outbound FIFO buffer for SPI port 0.
+#define CONFIG_SPI0_TXBUFSIZE 32
+
+/// [bytes] Size of the inbound FIFO buffer for SPI port 0.
+#define CONFIG_SPI0_RXBUFSIZE 32
+
+/// [bytes] Size of the outbound FIFO buffer for SPI port 1.
+#define CONFIG_SPI1_TXBUFSIZE 32
+
+/// [bytes] Size of the inbound FIFO buffer for SPI port 1.
+#define CONFIG_SPI1_RXBUFSIZE 32
+
+/// SPI data order (AVR only).
+#define CONFIG_SPI_DATA_ORDER SER_MSB_FIRST
+
+/// SPI clock division factor (AVR only).
+#define CONFIG_SPI_CLOCK_DIV 16
+
+/// SPI clock polarity: 0 = normal low, 1 = normal high (AVR only).
+#define CONFIG_SPI_CLOCK_POL 0
+
+/// SPI clock phase: 0 = sample on first edge, 1 = sample on second clock edge (AVR only).
+#define CONFIG_SPI_CLOCK_PHASE 0
+
+/// Default transmit timeout (ms). Set to -1 to disable timeout support.
+#define CONFIG_SER_TXTIMEOUT 100
+
+/// Default receive timeout (ms). Set to -1 to disable timeout support.
+#define CONFIG_SER_RXTIMEOUT 100
+
+/// Use RTS/CTS handshake
+#define CONFIG_SER_HWHANDSHAKE 0
+
+/// Default baud rate (set to 0 to disable).
+#define CONFIG_SER_DEFBAUDRATE 0
+
+/// Enable second serial port in emulator.
+#define CONFIG_EMUL_UART1 0
+
+/**
+ * Transmit always something on serial port 0 TX
+ * to avoid interference when sending burst of data,
+ * using AVR multiprocessor serial mode
+ */
+#define CONFIG_SER_TXFILL 0
+
+/// For serial debug.
+#define CONFIG_SER_STROBE 0
+
+#endif /* CFG_SER_H */