+++ /dev/null
-BASE_DIR=`dirname $0`
-INT_FILE=${BASE_DIR}/openocd/${PROGRAMMER_TYPE}.cfg
-CPU_FILE=${BASE_DIR}/openocd/${PROGRAMMER_CPU}.cfg
-
-if [ ! -f ${INT_FILE} ]; then
- printf "Interface ${PROGRAMMER_TYPE} not supported\n";
- exit 1;
-fi
-
-if [ ! -f ${CPU_FILE} ]; then
- printf "CPU ${PROGRAMMER_CPU} not supported\n";
- exit 1;
-fi
-
+++ /dev/null
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config srst_only srst_pulls_trst
-
-if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
-} else {
- set _CHIPNAME sam7
-}
-
-if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
-} else {
- set _ENDIAN little
-}
-
-if { [info exists CPUTAPID ] } {
- set _CPUTAPID $CPUTAPID
-} else {
- set _CPUTAPID 0x3f0f0f0f
-}
-
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
-target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi
-
-proc cpu_setup {} {
- halt
- sleep 10
-
- arm7_9 dcc_downloads enable
-
- armv4_5 core_state arm
- arm7_9 fast_memory_access enable
-
- # Init - taken from the script openocd_at91sam7_ecr.script
- mww 0xfffffd44 0x00008000 # disable watchdog
- mww 0xfffffd08 0xa5000001 # enable user reset
- mww 0xfffffc20 0x00000601 # CKGR_MOR : enable the main oscillator
- sleep 10
- mww 0xfffffc2c 0x00481c0e # CKGR_PLLR: 96.1097 MHz
- sleep 10
- mww 0xfffffc30 0x00000007 # PMC_MCKR : MCK = PLL / 2 ~= 48 MHz
- sleep 10
- mww 0xffffff60 0x003c0100 # MC_FMR: flash mode (FWS=1,FMCN=60)
- # arm7_9 force_hw_bkpts enable # program resides in flash
- sleep 10
-}
-
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 0
-
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank at91sam7 0 0 0 0 0
+++ /dev/null
-# Change the default telnet port...
-telnet_port 4444
-
-# Port for TCL connection.
-tcl_port 6666
-
-# GDB connects here
-gdb_port 3333
-
-source [find PROGRAMMER_TYPE]
-
-source [find PROGRAMMER_CPU]
-
-$_TARGETNAME configure -event reset-start {
- cpu_setup
-}
-
-$_TARGETNAME configure -event gdb-detach {
- shutdown
-}
-
-init
-reset run
+++ /dev/null
-# Change the default telnet port...
-telnet_port 4444
-
-# Port for TCL connection.
-tcl_port 6666
-
-# GDB connects here
-gdb_port 3333
-
-source [find PROGRAMMER_TYPE]
-
-source [find PROGRAMMER_CPU]
-
-$_TARGETNAME configure -event reset-start {
- cpu_setup
- # this will work only with (intel) hex files, which have ROM address information
- flash write_image IMAGE_FILE
-}
-
-$_TARGETNAME configure -event reset-end "shutdown"
-
-init
-reset run