Add local cfg.

git-svn-id: https://src.develer.com/svnoss/bertos/trunk@1969 38d2e660-2303-0410-9eaa-f027e97ec537

diff --git a/examples/at91sam7s/cfg/cfg_ser.h b/examples/at91sam7s/cfg/cfg_ser.h
new file mode 100644 (file)
index 0000000..719658b
--- /dev/null
+++ b/examples/at91sam7s/cfg/cfg_ser.h
@@ -0,0 +1,128 @@
+/**
+ * \file
+ * <!--
+ * This file is part of BeRTOS.
+ *
+ * Bertos is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ *
+ * As a special exception, you may use this file as part of a free software
+ * library without restriction.  Specifically, if other files instantiate
+ * templates or use macros or inline functions from this file, or you compile
+ * this file and link it with other files to produce an executable, this
+ * file does not by itself cause the resulting executable to be covered by
+ * the GNU General Public License.  This exception does not however
+ * invalidate any other reasons why the executable file might be covered by
+ * the GNU General Public License.
+ *
+ * Copyright 2008 Develer S.r.l. (http://www.develer.com/)
+ * All Rights Reserved.
+ * -->
+ *
+ * \brief Configuration file for serial module.
+ *
+ * \version $Id$
+ *
+ * \author Daniele Basile <asterix@develer.com>
+ */
+
+#ifndef CFG_SER_H
+#define CFG_SER_H
+
+/**
+ * Example of setting for serial port and
+ * spi port.
+ * Edit these define for your project.
+ */
+/// Serial settings
+#define CONFIG_SER_PORT      0
+#define CONFIG_SER_BAUDRATE  115200
+
+/// Spi settings
+#define CONFIG_SPI_PORT      0
+#define CONFIG_SPI_BAUDRATE  5000000UL
+
+
+/// [bytes] Size of the outbound FIFO buffer for port 0.
+#define CONFIG_UART0_TXBUFSIZE  32
+
+/// [bytes] Size of the inbound FIFO buffer for port 0.
+#define CONFIG_UART0_RXBUFSIZE  32
+
+/// [bytes] Size of the outbound FIFO buffer for port 1.
+#define CONFIG_UART1_TXBUFSIZE  32
+
+/// [bytes] Size of the inbound FIFO buffer for port 1.
+#define CONFIG_UART1_RXBUFSIZE  32
+
+
+/// [bytes] Size of the outbound FIFO buffer for SPI port (AVR only)
+#define CONFIG_SPI_TXBUFSIZE    32
+
+/// [bytes] Size of the inbound FIFO buffer for SPI port (AVR only)
+#define CONFIG_SPI_RXBUFSIZE    32
+
+/// [bytes] Size of the outbound FIFO buffer for SPI port 0.
+#define CONFIG_SPI0_TXBUFSIZE  32
+
+/// [bytes] Size of the inbound FIFO buffer for SPI port 0.
+#define CONFIG_SPI0_RXBUFSIZE  32
+
+/// [bytes] Size of the outbound FIFO buffer for SPI port 1.
+#define CONFIG_SPI1_TXBUFSIZE  32
+
+/// [bytes] Size of the inbound FIFO buffer for SPI port 1.
+#define CONFIG_SPI1_RXBUFSIZE  32
+
+/// SPI data order (AVR only).
+#define CONFIG_SPI_DATA_ORDER  SER_MSB_FIRST
+
+/// SPI clock division factor (AVR only).
+#define CONFIG_SPI_CLOCK_DIV   16
+
+/// SPI clock polarity: 0 = normal low, 1 = normal high (AVR only).
+#define CONFIG_SPI_CLOCK_POL   0
+
+/// SPI clock phase: 0 = sample on first edge, 1 = sample on second clock edge (AVR only).
+#define CONFIG_SPI_CLOCK_PHASE 0
+
+/// Default transmit timeout (ms). Set to -1 to disable timeout support.
+#define CONFIG_SER_TXTIMEOUT    -1
+
+/// Default receive timeout (ms). Set to -1 to disable timeout support.
+#define CONFIG_SER_RXTIMEOUT    -1
+
+/// Use RTS/CTS handshake
+#define CONFIG_SER_HWHANDSHAKE   0
+
+/// Default baud rate (set to 0 to disable).
+#define CONFIG_SER_DEFBAUDRATE   0
+
+/// Enable ser_gets() and ser_gets_echo().
+#define CONFIG_SER_GETS          0
+
+/// Enable second serial port in emulator.
+#define CONFIG_EMUL_UART1        0
+
+/**
+ * Transmit always something on serial port 0 TX
+ * to avoid interference when sending burst of data,
+ * using AVR multiprocessor serial mode
+ */
+#define CONFIG_SER_TXFILL        0
+
+/// For serial debug.
+#define CONFIG_SER_STROBE        0
+
+#endif /* CFG_SER_H */

diff --git a/examples/at91sam7s/cfg/cfg_timer.h b/examples/at91sam7s/cfg/cfg_timer.h
new file mode 100644 (file)
index 0000000..9d8357e
--- /dev/null
+++ b/examples/at91sam7s/cfg/cfg_timer.h
@@ -0,0 +1,55 @@
+/**
+ * \file
+ * <!--
+ * This file is part of BeRTOS.
+ *
+ * Bertos is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ *
+ * As a special exception, you may use this file as part of a free software
+ * library without restriction.  Specifically, if other files instantiate
+ * templates or use macros or inline functions from this file, or you compile
+ * this file and link it with other files to produce an executable, this
+ * file does not by itself cause the resulting executable to be covered by
+ * the GNU General Public License.  This exception does not however
+ * invalidate any other reasons why the executable file might be covered by
+ * the GNU General Public License.
+ *
+ * Copyright 2008 Develer S.r.l. (http://www.develer.com/)
+ * All Rights Reserved.
+ * -->
+ *
+ * \brief Configuration file for timer module.
+ *
+ * \version $Id$
+ *
+ * \author Daniele Basile <asterix@develer.com>
+ */
+
+#ifndef CFG_TIMER_H
+#define CFG_TIMER_H
+
+/// Hardware timer selection for drv/timer.c
+#define CONFIG_TIMER TIMER_DEFAULT
+
+/// Debug timer interrupt using a strobe pin.
+#define CONFIG_TIMER_STROBE  0
+
+/// Enable asynchronous timers
+#define CONFIG_TIMER_EVENTS  1
+
+/// Support hi-res timer_usleep()
+#define CONFIG_TIMER_UDELAY  1
+
+#endif /* CFG_TIMER_H */